Axial Racing SCX10 III Build Vol.01
Here comes the New SCX10 III Build!
Items:
1.Lets make it from The Axles!
2.All you need is to see the manual, there are nothing to read to build it!
3. Kind of, SCX10-II Axle, AR44 and Capra Axle, Currie F9, combine together!
4.Gears for the potal part, its the same as Capra, so you can use...「
HR
over drive portal gear sets! for Axial Capra」
4.Its slightly different, dont make a mistake!
5.You can see the difference!
6.Axles are done!
7.Next is shocks! put some silicon oil before you put caps on it! So that you dont damage the O rings!
8.Take all air out!
9.When I see the axle truss, I know these are designed for!!
10.Oils are filled! See how it works. rebounds are almost all the same!
12.Shocks are done, its same as Capra!
13.See how it build transmission! Looks so real! You can use spacer to let you kill the dig and 2 speed function.
14.Lot of gears, hardware and bearings!
15.Great looking transmission!
16.left lever is for the DIG and right one is for the 2 speed!
17.When you want to tighten the slipper clutch, see my picture!
18.As you can see, you can use 11T to 18T pinion gears for your reference!
19.These are how you install balls to the rods! First, try little with this!
20.Flip the rodend and snap it in!
21.Manual is so good, its actual size!
22.When you screw in the rodend to the rod, use 2 drivers!
23.See! Its actual size!
24.BUT! this 68.4mm rod are not actual size, be careful!
25.All done!
26.Chassis build!
27.I used steering servo,
YSS JX Servo[46kg][14V]」 so that I dont need to use Castle Creations CCBEC10A!
28.Servo seem to be little squared too much!
29.Cut some edges! Cut too much? I think so too!
30.Perfect fit!
31.Here is incorrect manual! Be careful!
32.Use this screw!
33.Chassis one side are done!
34.Almost done!
35.Motor and steering servo is installed!
36.Fully metal servo horn!
37.Great battery tray! You can adjust and fit your battery!
38.Motor cover, oh! Its Engine! Looks so cool!
39.Inner fenders are included!
40.Transmission, battery and Axles are installed!
41.Beadlock wheels are so good for crawlers!
42.Chassis are done! Lets install ESC and servos!
43.All covered! Looks GOOD!
44.DIG and 2 speed transmission micro servo, I used water proof
YSS Power HD TR-4[2.6㎏][7.4V], really great servo!
45.How I install the servo for the 2 speed!
46.Its powerful, and so cool!
47.For the DIG servo, I made servo horn like this!
48.DIG and 2 speed, Install really neat!
49.Body buid!
50.For the screws for the body are so small, so I identify like this!
51.And I put the screws to the parts, so that I dont mixed up next day build!
52.Masking the fenders, I am going to paint them!
53.JEEP JL, I decided to painted orange!
54.Looks so gooooood!
55.All paints are done!
56.Great looking colored fenders too!
57.I painted the body from also outside!
58.Paint, you should use lexan paints!
59.Rear looks good too!
60.Mandatory pose!
61.Inner fenders are great!
62.Mandatory pose #2! All done and works great too!
Lets enjoy!
YSS Crawlers - Yoshiaki Kataoka
This product was added to our catalog on Tuesday 14 April, 2020.
