VP Currie Portal F9 SCX10-II Front and Rear Axle set![Black]

VP Currie Portal F9 SCX10-II Front and Rear Axle set![Black]

Currie F9 Portal Front Axle for SCX10-II based vehicles

The F9 Portal axles create extreme amounts of ground clearance under the center of your axle, increasing the clearance by 1/2"+ (13mm). This provides the equivalent of a tire over 1 inch taller than what is on your vehicle. The advantage of the Vanquish Currie F9 Portals is the gear reduction inside the portal (1.67:1) which can be adjusted with optional gear sets (1.4:1 Overdrive). By adding reduction at the portal, less torque is transferred through the other upstream components in the drivetrain. These axles are a direct replacement to any Axial AR44 axle, using all stock links.

These axles come with all parts needed to assemble a full front axle.

Features

Portal box built into the included knuckle with bolt on high steer arm for double shear mounting
Gear reduction in the portal of 1.67:1 (18/30), Optional Overdrive Ratio of 1.4:1 (20/28) recommended for use in front axle only.
Included Vanquish AR44 machined gear set
Overall axle reduction of 6.26:1 with stock portal ratio
13mm increase in ground clearance
Specifically design offset C-hubs is machined into the housing for strength, durability, clearance and scale appearance
Hex to hex width of 7.66 inches, only roughly 5mm wider than a stock AR44 axle with a narrow hex
Replaceable Chromoly threaded inserts used at knuckle and C-hub to ensure a stripped thread doesn't ruin your investment
Brass knuckle bushing from the AR60 axles are used in place of SCX10-II sized for more durability.
Chromoly AR60 size VVD axle shafts come preassembled
Chromoly stub shafts with 6mm design at the drive pin which tapers down to a 5mm thread for ultimate strength
Chromoly spool
Aluminum 12mm hex with set screw
Compatible with stock SCX10-II Chassis mounted servo or F9 Servo on axle mount
Uses all SCX10-II linkage
Adjustable steering stop integrated into knuckle
Complete Fast Eddy Bearings kit
Licensed by Currie Enterprises
Comes with One Piece Bearing Retainers (Patent Pending)
Double shear shock mounts
Integrated Panhard mount
Upper link mounts built into third member
Increased upper link clearance for more suspension up travel ability

Requires the use of a 350 SLW hub or greater on Vanquish 1.9 wheels, Incision wheels will require a #4 or greater. Other wheel manufacturers offsets will vary. Axles must be used in pairs, you cannot run a front portal axle without a rear and vice versa.



Currie F9 Portal Rear Axle for SCX10-II based vehicles

The F9 Portal axles create extreme amounts of ground clearance under the center of your axle, increasing the clearance by 1/2"+ (13mm). This provides the equivalent of a tire over 1 inch taller than what is on your vehicle. The advantage of the Vanquish Currie F9 Portals is the gear reduction inside the portal (1.67:1) which can be adjusted with optional gear sets (1.4:1 Overdrive*). By adding reduction at the portal, less torque is transferred through the other upstream components in the drivetrain. These axles are a direct replacement to any Axial AR44 axle, using all stock links.

These axles come with all parts needed to assemble a full rear axle.

Features

Portal box integrated into the rear housing for the most clearance at the axle ends possible and a more scale appearance
Gear reduction in the portal of 1.67:1 (18/30), Optional Overdrive Ratio* of 1.4:1 (20/28) Included Vanquish AR44 machined gear set
Overall axle reduction of 6.26:1 with stock portal ratio
13mm increase in ground clearance
Hex to hex width of 7.66 inches, only roughly 5mm wider than a stock AR44 axle with a narrow hex
Chromoly inner rear axle shafts are triple bearing supported
Chromoly stub shafts with 6mm design at the drive pin which tapers down to a 5mm thread for ultimate strength
Chromoly spool
Aluminum 12mm hex with set screw
Uses all SCX10-II linkage
Complete Fast Eddy Bearings kit
Licensed by Currie Enterprises
Comes with One Piece Bearing Retainers (Patent Pending)
Double shear shock mounts
Upper link mounts built into third member
Increased upper link clearance for more suspension up travel ability

Requires the use of a 350 SLW hub or greater on Vanquish 1.9 wheels, Incision wheels will require a #4 or greater. Other wheel manufacturers offsets will vary. Axles must be used in pairs, you cannot run a front portal axle without a rear and vice versa.

*Overdrive gear sets are recommended for use in the front axle only



Product pictures:

















Search: Currie Portal F9 SCX10-II Front Axle Black Anodized | Currie Portal F9 SCX10-II Rear Axle Black Anodized | VPS08350 | VPS08360